A new kitchen

A new kitchen dictated a need for new potholders.

Since potholders are basically smallish squares with a loop for hanging, potholders can be used for experimenting with new techniques. Now, I wasn’t really in that place, too much going on in my life. What I needed was zen knitting.

And this is what I came up with; using garter stitch and modular knitting it became fun and I ended up with a new (at least to me) way of picking up stitches along garter stitch edges that makes the fabric more reversible. Here it is:

A more reversible method of picking up stitches along garter stitch edges

d8c_5551_grytlappteknik1

Insert a double-pointed needle (I used a circular) into the little knotsat the edge, created by the garter stitches, 1 stitch to each garter ridge. You may have to add the last stitch in the form of a loop.

d8c_5552_grytlappteknik2

Pull the needle through so you can start knitting from the correct end of the work.

d8c_5553_grytlappteknik3

Knit (you’ll need to knit into the back loop of the stitch on the first row)!

That’s all there is to it.

My Hempathy yarn is very suitable for kitchen duty; sturdy, washable and slightly antibacterial (in a natural, non-aggressive way) thanks to the hemp content, but too thin. So after a couple of trials I decided to use three strands held together. The potholders are somewhat slippery until they’ve been washed.

This is he first pair of potholders knitted to match my new kitchen. I will post more versions later on (I ended up knitting several for friends and family). This is a perfect gift and the design works for many styles from ultra modern to more traditional.

Here’s the recipe:

Potholders / Hot pad

Knitted with 3 strands of Hempathy on US size 8 / 5 mm needles to a gauge of approximately 18 stitches and 36 rows to 4 x 4 inches / 10 x 10 cm. Note that this means the same number of stitches and rows. The gauge isn’t important; a lloser gauge will make the potholders larger and a tighter gauge will make them smaller. What is important is that they are thick and firm enough to isolate the heat.

Each potholder is 32 sts x 32 garter ridges (64 rows). The cast-on row is counted as row 1 and you’ll bind off on row 32.

I’ve used 2–3 colors and each potholder weighs just under 50 g, so 3 balls of Hempathy would make a matching set of 2 potholders and a hot pad. This is also a perfect way to use odds and ends.

Cast on 18–22 sts and work 62 rows of garter st (31 ridges). Bind off but do not break the yarn. Pick up 1 st in each garter ridge (see above) until you have 32 sts.

Now work 20–28 rows of garter st (10–14 ridges).

The total number of stitches + rows should be the same in each direction, in this case 32.

Bind off all sts but do not break the yarn (except for the hot pad). Now crochet 15 single crochet. Pull yarn through and fasten to make a loop.

I hope you’ll have fun playing around with colors, striping, and different widths on the different sections.

Photos as always, Anders Rydell

Advertisements

A cool way to splice Misty Wool

Misty Wool is a tube yarn (as far as I can judge it is a 2-stitch tube), so this way of splicing works for most tube yarns. The yarn will be double thickness for the 3 – 5 stitches concerned but for most yarns that will not really be visible. To be on the safe side you should try to place the splices at less visible points in the knitting.

splice_srgb72

Top pic: Insert the new yarn into the middle of the old yarn (perfection is not necessary, just try to hit the center of the tube most of the time). Go for 3–5 cm, that is 1–2 inches or thereabouts.

Middle pic: pull the yarn through.

Bottom pic: Pull at both ends until the new yarn is hidden inside the old yarn. This is important or you will pull out the new yarn when you knit.

Knit on. No need for weaving in ends, Yeah!